Difference between revisions of "Wangine WPA-120"
(→Daten) |
|||
| (9 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | == | + | == Data == |
| − | {{ | + | {{navigation}} |
| − | ''' | + | '''General''' |
| − | * | + | * Manufacturer: [[Wangine]] |
| − | * | + | * Model: WPA 120 |
| − | * | + | * Color: Silver |
| − | * | + | * Type: Stereo |
| − | * | + | * Power consumption: max 800 watts |
| − | * | + | * Dimensions: 422x140x318mm (WxHxD) |
| − | * | + | * Weight: 16,3 kg |
| + | * Original price: 789 DM (October 1983) | ||
| − | ''' | + | '''Technical data''' |
| − | * | + | * Continuous power |
| − | + | 8 Ohm: 2x120W | |
| − | ** | + | * dynamic power |
| − | * | + | ** 8 Ohm: 2x240W |
| − | ** 8 Ohm | + | * Distortion factor |
| − | + | ** Total Harmonic Distortion <0,015% at rated power output 8 Ohm | |
| − | + | Inter Modulation Distortion <0,009% at rated power output 8 Ohm | |
| − | * | + | * Attenuation Factor: 200 (8 ohms, 1,000 Hz) |
| − | + | S/N Ratio: 110dB (IHF, A-weighted) | |
| − | * | + | * Frequency range: 5Hz - 200,000 Hz (+0, -3 dB) |
| − | * | + | * Input impedance: 50 kOhm |
| − | * | + | * Input sensitivity: 1 Volt |
| − | * | + | * Output: 4 - 16 Ohm |
| − | |||
| − | |||
| − | + | '''Other''' | |
| + | * Spectrum Analyzer | ||
| + | 32 Hz | ||
| + | ** 63 Hz | ||
| + | ** 125 Hz | ||
| + | ** 250 Hz | ||
| + | 500 Hz | ||
| + | ** 1 kHz | ||
| + | ** 2 kHz | ||
| + | ** 4 kHz | ||
| + | ** 8 kHz | ||
| + | ** 16 kHz | ||
| + | * Display switching | ||
| + | ** 1 => 1 Watts to 240 Watts | ||
| + | ** 0.1 => 0.1 Watts to 24 Watts | ||
| + | ** 0.01 => 0.01 Watts to 2.4 Watts | ||
| + | * Control Switch | ||
| + | ** A, B, A+B | ||
| − | |||
| − | + | '''Semiconductor''' | |
| + | * 2 FET | ||
| + | * 10 IC | ||
| + | * 71 transistors | ||
| + | * 91 LEDs | ||
| + | * 46 diodes | ||
| + | * 3 bridge rectifier | ||
| − | |||
| + | '''Note''' | ||
| − | [[ | + | The above performance data are original data. |
| + | Own measured power at 50 Hz sine input signal: | ||
| + | |||
| + | ~ 145 W into 8 Ohm | ||
| + | |||
| + | ~ 225 W into 4 Ohm | ||
| + | |||
| + | Measured at an appropriate load resistor with optical control by oscilloscopes for a 'clean' output signal. Only one channel was measured under power. Because of the construction as a double mono power amplifier (separate power supplies) this power should be reached on both power amplifiers at the same time. | ||
| + | Whether this power represents a continuous power was not checked, but these powers were reached cleanly over a period of about 15 minutes. After that, the measurement was stopped to protect the load resistors, as they were not sufficiently dimensioned in terms of power. | ||
| + | |||
| + | |||
| + | The output stage has a switch-on delay and a protection circuit. This protective circuit is partially sensitive to mains interference. A sufficiently dimensioned mains filter can remedy this. | ||
| + | |||
| + | == Remarks == | ||
| + | Other models of the same series: | ||
| + | * [[Wangine WTA-120|WTA-120]] | ||
| + | * [[Wangine WEQ-120|WEQ-120]] | ||
| + | |||
| + | == Pictures == | ||
| + | [[Image:Wangine_WPA120_01.jpg]] | ||
| + | |||
| + | [[Image:Wangine_WPA120_02.jpg]] | ||
| + | |||
| + | [[Image:Wangine_WPA120_03.jpg]] | ||
| + | |||
| + | [[Image:Wangine_WPA120_04.jpg]] | ||
| + | |||
| + | [[Image:Wangine_WPA120_05.jpg]] | ||
| + | |||
| + | |||
| + | [[Category:Power Amplifiers]] | ||
Latest revision as of 13:27, 1 March 2012
Data[edit]
General
- Manufacturer: Wangine
- Model: WPA 120
- Color: Silver
- Type: Stereo
- Power consumption: max 800 watts
- Dimensions: 422x140x318mm (WxHxD)
- Weight: 16,3 kg
- Original price: 789 DM (October 1983)
Technical data
- Continuous power
8 Ohm: 2x120W
- dynamic power
- 8 Ohm: 2x240W
- Distortion factor
- Total Harmonic Distortion <0,015% at rated power output 8 Ohm
Inter Modulation Distortion <0,009% at rated power output 8 Ohm
- Attenuation Factor: 200 (8 ohms, 1,000 Hz)
S/N Ratio: 110dB (IHF, A-weighted)
- Frequency range: 5Hz - 200,000 Hz (+0, -3 dB)
- Input impedance: 50 kOhm
- Input sensitivity: 1 Volt
- Output: 4 - 16 Ohm
Other
- Spectrum Analyzer
32 Hz
- 63 Hz
- 125 Hz
- 250 Hz
500 Hz
- 1 kHz
- 2 kHz
- 4 kHz
- 8 kHz
- 16 kHz
- Display switching
- 1 => 1 Watts to 240 Watts
- 0.1 => 0.1 Watts to 24 Watts
- 0.01 => 0.01 Watts to 2.4 Watts
- Control Switch
- A, B, A+B
Semiconductor
- 2 FET
- 10 IC
- 71 transistors
- 91 LEDs
- 46 diodes
- 3 bridge rectifier
Note
The above performance data are original data. Own measured power at 50 Hz sine input signal:
~ 145 W into 8 Ohm
~ 225 W into 4 Ohm
Measured at an appropriate load resistor with optical control by oscilloscopes for a 'clean' output signal. Only one channel was measured under power. Because of the construction as a double mono power amplifier (separate power supplies) this power should be reached on both power amplifiers at the same time. Whether this power represents a continuous power was not checked, but these powers were reached cleanly over a period of about 15 minutes. After that, the measurement was stopped to protect the load resistors, as they were not sufficiently dimensioned in terms of power.
The output stage has a switch-on delay and a protection circuit. This protective circuit is partially sensitive to mains interference. A sufficiently dimensioned mains filter can remedy this.
Remarks[edit]
Other models of the same series:
Pictures[edit]
